UPLIFT UPL120 Black Laminate (FRM703 flush; PDC119 mapping + ACC088 cover) review

This is one current U.S. UPLIFT V3 UPL120 selector state: a one-inch Black Laminate top (3842), black V3 C-frame with 27-inch feet (20903), one power module plus one ACC088 cover in the “Power w/ USB + Cover Black” option (18612), and black FRM703 Advanced Comfort Flush keypad (12041). The visible code says BUNDLE-PDC019-ACC088-BLK, but the current embedded mapping identifies BUNDLE-PDC119-ACC088-BLK / PDC119-BLK; verify the part in the final order summary. It describes a selectable configuration, not a separately verified retail SKU, a completed order, or current stock.

Choose this layout for a wraparound corner, not a measured rectangle

The UPL120 is a two-leg electric desk with a 120-degree wraparound work surface. UPLIFT's drawing gives 71.7 inches overall width and a maximum outside-depth envelope of 38.4 inches. Those are useful room-planning boundaries, but they do not mean that every point on the curved front and angled back is 38.4 inches deep. If a monitor arm, writing pad or keyboard zone needs a minimum continuous depth, the drawing does not supply that dimension. Tape the outline on the floor and map the places where your equipment and chair must sit before treating this as a fit.

The selected surface is maker-labeled Black Laminate, one inch thick. The drawing identifies black low-pressure laminate, but does not state the selected top's mass, care routine, edge treatment or resistance to a particular spill. The shape creates a wide reach area around one main position; it is harder to place in a shallow alcove than a straight-front desktop, and it is not a true L with a separate perpendicular return.

One module and one cover use both holes differently

The UPL120 drawing shows two 3.15-inch openings. In this option bundle, one hole maps to a fixed/flush PDC119 power grommet and the other has a separate rotating ACC088 cover for a cable pass-through. The pair gives you a power point and a way to route a monitor or peripheral lead through the top, but the cover is not another outlet, charger or storage cup. UPLIFT’s current PDC119 listing specifies two AC outlets, not four.

The current PDC119 listing describes two AC outlets, two USB-A ports, one USB-C port and 20W USB-C Power Delivery. Its current UPL120 mapping identifies a fixed/flush grommet module rather than the press-to-raise PDC013. The visible option code still says PDC019, so confirm the accessory in the final order summary. The reviewed current PDC119 listing does not establish USB data transfer, cord length, current limit or a particular under-top installation clearance. Do not transfer those specifications from PDC019 instructions or sheets merely because the visible selector label retains that older code. The frame also needs its own mains connection; plan its lead and preserve slack across the full desk movement.

The flush FRM703 changes the daily control routine

FRM703 sits along the desktop's front edge rather than pointing upward at an angle. UPLIFT describes four saved heights with one-touch recall, a display, a lock, user-set upper and lower travel stops, and calibration. That makes this plan more useful than the Basic Display FRM072 if saved positions and a low-profile front edge are essential. The Basic Display FRM072 version of the one-power-module-and-cover combination is reviewed separately; its preset count is not established, so do not assume the two keypad choices behave alike.

The flush layout may avoid a control that protrudes above the edge, but it does not remove the need to check the lift path for a chair, drawer or shelf. The FRM703 instructions show two-screw attachment at either pre-drilled position and a reset after assembly. They also caution against deep pilot holes if a new position is used. Follow the keypad instructions together with the V3 frame reset, cord-routing and moving-part guidance instead of assuming a controller feature prevents every collision.

Keep the manufacturer limits in their proper units

For the one-inch top, the selected UPL120 page states a 22.6-to-48.7-inch working-surface range. The V3 C-frame sheet lists 21.6 to 47.7 inches for the bare frame. These are different measurement bases and are maker specifications, not independent measurements of an assembled desk. UPLIFT lists a 355-pound lifting-capacity figure for the frame, while its manual uses weight-limit wording. Neither source gives a static-load rating, the desktop's mass or remaining accessory payload. If your limit is about equipment weight on the moving desktop, do not treat 355 pounds as a verified payload.

Who should shortlist this selector state?

Consider it if the UPL120 outline fits your room, two surface AC outlets are enough, you want a separate covered cable route, and you value a flush four-memory controller. It is a poor match if you need three or more integrated outlets, documented USB data transfer, a pop-up power panel, a known continuous top depth or a documented static-load figure. A separately selected dual-power UPL120 can fill both holes with power modules and forgo the ACC088 cable route, so it has no ACC088 opening. A PDC013 pop-up plan changes the installation and underside-clearance requirements. For the same Black Laminate / one-power-module-plus-cover bundle with an angled Basic Display, compare the FRM072 configuration review; for the distinct dual-fixed-power setup, see the FRM703 dual-PDC019 review. Those are concrete option changes, not rankings.

Sources for this assessment include the current UPL120 selected-state page, UPLIFT's desktop drawing and V3 frame instructions, plus the current PDC119 Power Grommet listing and FRM703 installation guide.